杜绝后台偷传数据 — PHICOMM 斐讯 k2 无线路由 再刷PADAVAN固件_开箱晒物_什么值得买
杜绝后台偷传数据 — PHICOMM 斐讯 k2 无线路由 再刷PADAVAN固件
不知道大家是不是跟我一样的想法？ 之前K1出来0元购的时候，我看了介绍感觉像是庞氏骗局（本身看配置成本应该30-40内的路由器，标定价格却远高于张大妈经常推荐69元神器newifi，而newifi的配置128M内存还高于K2的64M内存），所以身边有朋友提到的时候我总是说服他们再三要谨慎。再加上一直有斐讯的路由器会后台偷偷上传用户数据的统计的传闻，我就一直不想动0元购的心思。一直到了上个月的时候看到京东居然有一个购买3台K2再优惠60元的活动，心动了一下，再加上家里newifi到了隔了2堵墙父母的房间基本没信号了（我用的就是newifi，当初微博活动晒拆开的无线路由送的，用了小半年以后刷了padavan固件），心想有京东给斐讯背书，应该不至于跑路了吧；带着占便宜没够的心理，后台上传数据的问题我有刷机经验，到手就刷固件，让你想偷传数据也没门。上网查了下刷机攻略，信心爆炸，当下就下了单，京东这次快递非常给力，第二天就送到了。下面是买3台-60优惠的图。&
&上下刚到货的3台K2，上网查了下，这次是新包装：再上个马上退役的newifi图：再给大家看看各个角度的K2新鲜无死角照：原先斐讯官方的固件界面：现在进入刷机过程：先说明下，本人只是个菜鸟，网上参考了多篇攻略，我只是个小白，就总结成同样非常简单易于操作的方式，希望介绍给大家，让大家都可以刷成功最主要的2篇攻略链接（在此感谢2位攻略作者，以及多位为刷机奉献了工具和优化固件的大神们）：固件介绍链接（这个还有不断更新固件）：第一步：准备工作下载刷机工具、固件链接：&密码：hrx4拔掉光纤调制解调器（俗称光猫，或者光纤猫）和无线路由器之间连接的网线,并且把路由器恢复出厂设置，然后用网线把路由器LAN口和电脑连接。不能用无线网络连接路由器刷机。第二步：打开breed web刷控制台通用助手，把然后解压breed web刷控制台通用助手(防火墙提示全部允许访问)。右键——以管理员身份运行&&软件先进行如图设置，接着点击开始刷breed，等刷breed完成&&出来下面这个不用管，允许访问即可&&&刷入成功会有这个提示之后就可以关掉全部窗口第三步：进入breed刷入固件刷入breed完成后等待几十秒后拔掉路由器电源， 然后按住reset按钮（复位键）不要松手，同时插上电源 通电后多等5秒松手。注意看电脑的网络连接，等到获取到ip后 ，然后输入192.168.1.1 即可进入如图界面（breed web 恢复控制台）&&建议各位刷机前，在breed里先备份EEPROM和编程器固件还要回复恢复出厂设置！！不然有可能导致网速较慢，选默认公版即可。&&按照下图步骤所示上传固件就再点击更新等待大约1分钟&&路由器会自动重启，在地址栏输入192.168.1.1（这个地址可以通过运行命令cmd后输入ipconfig查得&），输入默认用户名admin密码admin大功告成！测试一下网速设置一下自动重启，这里我设置的是每天3点半重启脚本：直接黏贴入即可# 每周1-5凌晨3点半重启（自己添加）30 3 * * 1,2,3,4,5 reboot & #删除开头的#启动命令另外刷了固件后，想回到breed web控制台的方法：拔掉路由器电源， 然后按住reset按钮不要松手，同时插上电源 通电后三秒松手，打开192.168.1.1 就进入了breed web控制台！！此外还可以安装广告屏蔽助手adbyby 自动代理服务器SS等，方法大家可以参考我贴出来的2位大神的帖子。以下是个人的使用感受：外观:还算时尚，白色的外观放在家里还是挺美观的，显得大气。固件使用心得：如果没刷机的话经常会出现插入网线但是认不到的情况，刷机之后基本不会了。所以证明一定要刷机啊。padavan的固件功能十分强大，可玩性很高。信号：隔3堵墙依旧满信号，比newifi强了2个级别。然而其实只是看起来强而已，实际上网速并没有多快，当然比newifi都已经断开了强多了。坐等0元购回款ing了，如果正常回款了的话，确实算上性价比之选，如果你在一个对路由器要求不高的居家环境，只要求到处能收到信号，完全能满足你的需求。打完收工~谢谢观看
本文著作权归作者本人和什么值得买共同所有，未经许可不得转载。文章仅代表作者看法，如有更多内容分享或是对文中观点有不同见解，值客原创欢迎您的投稿。
推荐关注：
鼠标移到标签上方，
尝试关注标签~
相关热门原创
作者其他原创（1）
赞12评论14
【抢先首发】SIEMNES 西门子飓风吸油烟机
【轻众测】Maxnon 麦能科技 iPhone背夹电池
【抢先首发】特斯拉 Model X 90D 五天使用权（限地区）
【抢先首发】亚马逊Prime会员权益1年+千元海外购现金补贴
【抢先首发】ThinkPad 黑侠E570 GTX 游戏笔记本
【抢先首发】Kodak 柯达 便携式照片打印机
【抢先首发】MOOV NOW语音健身教练
【抢先首发】极米 无屏 电视 CC
赞266评论221
赞30评论63
赞43评论58
赞1508评论763
赞1127评论1007
赞1021评论774
赞636评论469
赞235评论467
扫一下，分享更方便，购买更轻松
用户名/邮箱
两周内免登录190 / 624 页
[]改华硕[N14U N54U]5G 2G的7620老毛子Padavan固件(百度云同步 aria2 QOS)
@hiboyhiboyhiboy 大神
1.请问vpn设置 l2tp 后怎么设置预共享密码？（不填这个番不出去）
2.请问怎样用 ...
hiboy大大 你好&&我的L2TP 没有弄好 w/o IPsec前面w/o是“没有”的意思& &还是写入/输入的意思？？
然后 L2TP 端口号是不是1701 ？这个端口我没有映射成功
楼主SYncy开一段时间下载就不下载了，是不是sycny进程被关掉了，可以加守护进程吗？
为什么我的用起来 上网很慢
如何设置 短按wps键 开关ss？ 我是2月22的99版本
短按只能选用户脚本（arg：1），选定后是开关adbyby
如何才能设置成开关ss？
另外ss设置gfwlist模式时不能fq。另外两个可以，gfwlist是github上的版本
极1S 型号是5661a 问下用哪个版本 新手不敢乱刷
大大，为什么不能该权限啊，我想上传mentohust，但是显示read-only filesystem，有没有人可以帮帮我
YOUTUBE没问题……
FACEBOOK死活打不开……
DNS被污染了？
迅雷快鸟脚本不能使用了啊
@hiboyhiboyhiboy
回帖报告2个bug，极路由1s，刷了以后重启按钮按一下就死机，有线无线都连不上，路由器灯亮，也不知道什么问题，另外一个问题开了定时开关wifi以后，早上起来能连上wifi，却无法上网
&&看的这篇教程设置的但是就是获取不到ipv6.
H大...提供个教程?
69买一个newifi，mark一下以备后用。
支持大大发固件
好像用大神你这个固件啊&&但是目前需要多拨提速下载&&求弄个多拨功能呀
好帖留名&&
请问下这个固件已改16ram64rom的TP840V2可以用吗？
求助啊，lz大大！！！我路由器是斐讯psg1208，刷了最新的099，设置好ss，打开了adbyby，一个小时不到，ss和adbyby就全不能用了，再过几个小时，网速就特别慢，并且手机断开就再也链接不上路由器了，需要重启路由器才可以连接上，重启之后网速也恢复正常，但是ss和adbyby还是不能用。过几个小时又是一样的情况，网速变慢和不能连接。（ss和adbyby一定要重刷固件才能恢复）
64M的也没这么夸张，我也有K1，现在刷的2.16的版本，挂adbyby和ss，稳定运行十几天无重启了。&
看样子是你的机内存不够用！不会是64M的吧？&
感谢楼主分享！
楼主你好 我的是小米mini路由器&&刷了固件后玩lol一直重复着重新连接网络 ，游戏都玩不了下面是日志 就开启了adbyby
Jan&&1 00:00:04 syslogd started: BusyBox v1.24.1
Jan&&1 00:00:04 RT-AC54U: firmware version: 3.4.3.9-099_02-22
Jan&&1 00:00:04 kernel: klogd started: BusyBox v1.24.1 ( 11:09:05 CST)
Jan&&1 00:00:04 kernel: Linux version 3.4.110 (padavan@hms) (gcc version 4.4.7 (GCC) ) #7 Mon Feb 22 00:27:12 CST 2016
Jan&&1 00:00:04 kernel: MediaTek SoC: MT7620A, RevID: 0206, RAM: DDR2, XTAL: 20MHz
Jan&&1 00:00:04 kernel: CPU/OCP/SYS frequency: 580/193/193 MHz
Jan&&1 00:00:04 kernel: CPU revision is:
(MIPS 24KEc)
Jan&&1 00:00:04 kernel: Determined physical RAM map:
Jan&&1 00:00:04 kernel:&&memory:
Jan&&1 00:00:04 kernel: Zone PFN ranges:
Jan&&1 00:00:04 kernel:& &Normal& &0x -& 0x
Jan&&1 00:00:04 kernel: Movable zone start PFN for each node
Jan&&1 00:00:04 kernel: Early memory PFN ranges
Jan&&1 00:00:04 kernel:& &&&0: 0x -& 0x
Jan&&1 00:00:04 kernel: On node 0 totalpages: 32768
Jan&&1 00:00:04 kernel: free_area_init_node: node 0, pgdat 80345f70, node_mem_map
Jan&&1 00:00:04 kernel:& &Normal zone: 256 pages used for memmap
Jan&&1 00:00:04 kernel:& &Normal zone: 0 pages reserved
Jan&&1 00:00:04 kernel:& &Normal zone: 32512 pages, LIFO batch:7
Jan&&1 00:00:04 kernel: Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Jan&&1 00:00:04 kernel: Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Jan&&1 00:00:04 kernel: pcpu-alloc: s0 r0 d3 alloc=1*32768
Jan&&1 00:00:04 kernel: pcpu-alloc: [0] 0
Jan&&1 00:00:04 kernel: Built 1 zonelists in Zone order, mobility grouping on.&&Total pages: 32512
Jan&&1 00:00:04 kernel: Kernel command line: console=ttyS0, root=/dev/mtdblock4 rootfstype=squashfs
Jan&&1 00:00:04 kernel: PID hash table entries: 512 (order: -1, 2048 bytes)
Jan&&1 00:00:04 kernel: Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Jan&&1 00:00:04 kernel: Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Jan&&1 00:00:04 kernel: Writing ErrCtl register=
Jan&&1 00:00:04 kernel: Readback ErrCtl register=
Jan&&1 00:00:04 kernel: Memory: 1072k available (2820k kernel code, 4824k reserved, 533k data, 228k init, 0k highmem)
Jan&&1 00:00:04 kernel: NR_IRQS:40
Jan&&1 00:00:04 kernel: console [ttyS0] enabled
Jan&&1 00:00:04 kernel: Calibrating delay loop... 385.02 BogoMIPS (lpj=770048)
Jan&&1 00:00:04 kernel: pid_max: default: 32768 minimum: 301
Jan&&1 00:00:04 kernel: Mount-cache hash table entries: 512
Jan&&1 00:00:04 kernel: NET: Registered protocol family 16
Jan&&1 00:00:04 kernel: bio: create slab &bio-0& at 0
Jan&&1 00:00:04 kernel: SCSI subsystem initialized
Jan&&1 00:00:04 kernel: usbcore: registered new interface driver usbfs
Jan&&1 00:00:04 kernel: usbcore: registered new interface driver hub
Jan&&1 00:00:04 kernel: usbcore: registered new device driver usb
Jan&&1 00:00:04 kernel: PCI host bridge to bus 0000:00
Jan&&1 00:00:04 kernel: pci_bus 0000:00: root bus resource [mem 0xx2fffffff]
Jan&&1 00:00:04 kernel: pci_bus 0000:00: root bus resource [io&&0xx1016ffff]
Jan&&1 00:00:04 kernel: pci .0: [] type 01 class 0x060400
Jan&&1 00:00:04 kernel: pci .0: supports D1
Jan&&1 00:00:04 kernel: pci .0: PME# supported from D0 D1 D3hot
Jan&&1 00:00:04 kernel: pci .0: bridge configuration invalid ([bus 00-00]), reconfiguring
Jan&&1 00:00:04 kernel: pci .0: [14c3:7662] type 00 class 0x028000
Jan&&1 00:00:04 kernel: pci .0: reg 0x10: [mem 0xx000fffff 64bit]
Jan&&1 00:00:04 kernel: pci .0: reg 0x30: [mem 0xx0000ffff pref]
Jan&&1 00:00:04 kernel: pci .0: PME# supported from D0 D3hot D3cold
Jan&&1 00:00:04 kernel: pci .0: BAR 8: assigned [mem 0xx200fffff]
Jan&&1 00:00:04 kernel: pci .0: BAR 9: assigned [mem 0xx201fffff pref]
Jan&&1 00:00:04 kernel: pci .0: BAR 0: assigned [mem 0xx200fffff 64bit]
Jan&&1 00:00:04 kernel: pci .0: BAR 6: assigned [mem 0xx2010ffff pref]
Jan&&1 00:00:04 kernel: pci .0: PCI bridge to [bus 01-01]
Jan&&1 00:00:04 kernel: pci .0:& &bridge window [mem 0xx200fffff]
Jan&&1 00:00:04 kernel: pci .0:& &bridge window [mem 0xx201fffff pref]
Jan&&1 00:00:04 kernel: PCI: Enabling device .0 (0000 -& 0002)
Jan&&1 00:00:04 kernel: Switching to clocksource MIPS
Jan&&1 00:00:04 kernel: NET: Registered protocol family 2
Jan&&1 00:00:04 kernel: IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
Jan&&1 00:00:04 kernel: TCP established hash table entries: 4096 (order: 3, 32768 bytes)
Jan&&1 00:00:04 kernel: TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
Jan&&1 00:00:04 kernel: TCP: Hash tables configured (established 4096 bind 4096)
Jan&&1 00:00:04 kernel: TCP: reno registered
Jan&&1 00:00:04 kernel: UDP hash table entries: 256 (order: 0, 4096 bytes)
Jan&&1 00:00:04 kernel: NET: Registered protocol family 1
Jan&&1 00:00:04 kernel: PCI: CLS 32 bytes, default 32
Jan&&1 00:00:04 kernel: squashfs: version 4.0 () Phillip Lougher
Jan&&1 00:00:04 kernel: msgmni has been set to 246
Jan&&1 00:00:04 kernel: io scheduler noop registered
Jan&&1 00:00:04 kernel: io scheduler bfq registered (default)
Jan&&1 00:00:04 kernel: BFQ I/O-scheduler version: v7r7
Jan&&1 00:00:04 kernel: Serial:
driver, 1 ports, IRQ sharing disabled
Jan&&1 00:00:04 kernel: serial8250: ttyS0 at MMIO 0x10000c00 (irq = 12) is a 16550A
Jan&&1 00:00:04 kernel: Ralink GPIO driver initialized. Number of GPIO: 73, GPIO mode: 0058171D
Jan&&1 00:00:04 kernel: loop: module loaded
Jan&&1 00:00:04 kernel: Ralink SPI flash driver, SPI clock: 24MHz
Jan&&1 00:00:04 kernel: SPI flash chip: MX25L12835F (c2 ) (16384 Kbytes)
Jan&&1 00:00:04 kernel: Creating 7 MTD partitions on &raspi&:
Jan&&1 00:00:04 kernel: 0x-0x : &Bootloader&
Jan&&1 00:00:04 kernel: 0x-0x : &Config&
Jan&&1 00:00:04 kernel: 0x-0x : &Factory&
Jan&&1 00:00:04 kernel: 0x-0x : &Kernel&
Jan&&1 00:00:04 kernel: 0x-0x00 : &RootFS&
Jan&&1 00:00:04 kernel: 0x00-0x : &Storage&
Jan&&1 00:00:04 kernel: 0x-0x00 : &Firmware_Stub&
Jan&&1 00:00:04 kernel: tun: Universal TUN/TAP device driver, 1.6
Jan&&1 00:00:04 kernel: tun: (C)
Max Krasnyansky &&
Jan&&1 00:00:04 kernel: Ralink APSoC Ethernet Driver v3.2.2 (raeth)
Jan&&1 00:00:04 kernel: raeth: PDMA RX ring 256, PDMA TX ring 512. Max packet size 1536
Jan&&1 00:00:04 kernel: raeth: NAPI support, weight 32
Jan&&1 00:00:04 kernel: raeth: Byte Queue Limits (BQL) support
Jan&&1 00:00:04 kernel: PPP generic driver version 2.4.2
Jan&&1 00:00:04 kernel: PPP MPPE Compression module registered
Jan&&1 00:00:04 kernel: NET: Registered protocol family 24
Jan&&1 00:00:04 kernel: PPTP driver version 0.8.5
Jan&&1 00:00:04 kernel: usbcore: registered new interface driver libusual
Jan&&1 00:00:04 kernel: nf_conntrack version 0.5.0 (16384 buckets, 32768 max)
Jan&&1 00:00:04 kernel: xt_time: kernel timezone is -0000
Jan&&1 00:00:04 kernel: Bridge firewalling registered
Jan&&1 00:00:04 kernel: gre: GRE over IPv4 demultiplexor driver
Jan&&1 00:00:04 kernel: ip_tables: (C)
Netfilter Core Team
Jan&&1 00:00:04 kernel: TCP: cubic registered
Jan&&1 00:00:04 kernel: NET: Registered protocol family 10
Jan&&1 00:00:04 kernel: ip6_tables: (C)
Netfilter Core Team
Jan&&1 00:00:04 kernel: IPv6 over IPv4 tunneling driver
Jan&&1 00:00:04 kernel: NET: Registered protocol family 17
Jan&&1 00:00:04 kernel: L2TP core driver, V2.0
Jan&&1 00:00:04 kernel: PPPoL2TP kernel driver, V2.0
Jan&&1 00:00:04 kernel: 8021q: 802.1Q VLAN Support v1.8
Jan&&1 00:00:04 kernel: ASUS NVRAM, v0.08. Available space: 61440. Integrity: OK
Jan&&1 00:00:04 kernel: VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
Jan&&1 00:00:04 kernel: Freeing unused kernel memory: 228k freed
Jan&&1 00:00:04 kernel: Algorithmics/MIPS FPU Emulator v1.5
Jan&&1 00:00:04 kernel: rt2860v2_ap: module license 'Proprietary' taints kernel.
Jan&&1 00:00:04 kernel: APSoC AP Driver version: 2.7.2.0
Jan&&1 00:00:04 kernel: PCI: Enabling device .0 (0000 -& 0002)
Jan&&1 00:00:04 kernel: MT76x2 AP Driver version: 3.0.4.0.P1
Jan&&1 00:00:04 kernel: usbcore: registered new interface driver usblp
Jan&&1 00:00:04 kernel: Initializing USB Mass Storage driver...
Jan&&1 00:00:04 kernel: usbcore: registered new interface driver usb-storage
Jan&&1 00:00:04 kernel: USB Mass Storage support registered.
Jan&&1 00:00:04 kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jan&&1 00:00:04 kernel: ehci-platform ehci-platform: Generic Platform EHCI Controller
Jan&&1 00:00:04 kernel: ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
Jan&&1 00:00:04 kernel: ehci-platform ehci-platform: irq 18, io mem 0x101c0000
Jan&&1 00:00:04 kernel: ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored
Jan&&1 00:00:04 kernel: usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
Jan&&1 00:00:04 kernel: usb usb1: Product: Generic Platform EHCI Controller
Jan&&1 00:00:04 kernel: usb usb1: Manufacturer: Linux 3.4.110 ehci_hcd
Jan&&1 00:00:04 kernel: usb usb1: SerialNumber: ehci-platform
Jan&&1 00:00:04 kernel: hub 1-0:1.0: USB hub found
Jan&&1 00:00:04 kernel: hub 1-0:1.0: 1 port detected
Jan&&1 00:00:04 kernel: ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Jan&&1 00:00:04 kernel: ohci-platform ohci-platform: Generic Platform OHCI Controller
Jan&&1 00:00:04 kernel: ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
Jan&&1 00:00:04 kernel: ohci-platform ohci-platform: irq 18, io mem 0x101c1000
Jan&&1 00:00:04 kernel: usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
Jan&&1 00:00:04 kernel: usb usb2: Product: Generic Platform OHCI Controller
Jan&&1 00:00:04 kernel: usb usb2: Manufacturer: Linux 3.4.110 ohci_hcd
Jan&&1 00:00:04 kernel: usb usb2: SerialNumber: ohci-platform
Jan&&1 00:00:04 kernel: hub 2-0:1.0: USB hub found
Jan&&1 00:00:04 kernel: hub 2-0:1.0: 1 port detected
Jan&&1 00:00:04 kernel: raeth: HW IP/TCP/UDP checksum RX/TX offload enabled
Jan&&1 00:00:04 kernel: raeth: HW VLAN TX offload enabled
Jan&&1 00:00:04 kernel: raeth: HW Scatter/Gather TX offload enabled
Jan&&1 00:00:04 kernel: mtk_esw - hw bridge: W|LLLL
Jan&&1 00:00:04 kernel: mtk_esw - set broadcast storm control rate as: 10 mbps
Jan&&1 00:00:04 kernel: device eth2.1 entered promiscuous mode
Jan&&1 00:00:04 kernel: device eth2 entered promiscuous mode
Jan&&1 00:00:06 kernel: mtk_esw: Link Status Changed - Port WAN Link Up
Jan&&1 00:00:06 kernel: device ra0 entered promiscuous mode
Jan&&1 00:00:10 kernel: =====================================================
Jan&&1 00:00:10 kernel: Channel 36 : Dirty = 0, False CCA = 0, Busy Time = 0, Skip Channel = FALSE
Jan&&1 00:00:10 kernel: Channel 40 : Dirty = 0, False CCA = 0, Busy Time = 0, Skip Channel = FALSE
Jan&&1 00:00:10 kernel: Channel 44 : Dirty = 0, False CCA = 0, Busy Time = 0, Skip Channel = FALSE
Jan&&1 00:00:10 kernel: Channel 48 : Dirty = 0, False CCA = 0, Busy Time = 0, Skip Channel = FALSE
Jan&&1 00:00:10 kernel: Channel 149 : Dirty = 0, False CCA = 10, Busy Time = 0, Skip Channel = FALSE
Jan&&1 00:00:10 kernel: Channel 153 : Dirty = 0, False CCA = 0, Busy Time = 0, Skip Channel = FALSE
Jan&&1 00:00:10 kernel: Channel 157 : Dirty = 0, False CCA = 7, Busy Time = 0, Skip Channel = FALSE
Jan&&1 00:00:10 kernel: Channel 161 : Dirty = 0, False CCA = 4, Busy Time = 0, Skip Channel = FALSE
Jan&&1 00:00:10 kernel: Channel 165 : Dirty = 0, False CCA = 0, Busy Time = 0, Skip Channel = FALSE
Jan&&1 00:00:10 kernel: =====================================================
Jan&&1 00:00:10 kernel: Rule 1 CCA value : Min Dirtiness (Include extension channel) ==& Select Channel 36
Jan&&1 00:00:10 kernel: Min Dirty = 0
Jan&&1 00:00:10 kernel: ExChannel = 0 , 0
Jan&&1 00:00:10 kernel: BW& && &&&= 80
Jan&&1 00:00:10 kernel: device rai0 entered promiscuous mode
Jan&&1 00:00:11 kernel: br0: port 3(rai0) entered forwarding state
Jan&&1 00:00:11 kernel: br0: port 2(ra0) entered forwarding state
Jan&&1 00:00:11 kernel: br0: port 1(eth2.1) entered forwarding state
Jan&&1 00:00:11 dnsmasq[500]: started, version 2.75 cachesize 1024
Jan&&1 00:00:11 dnsmasq[500]: compile time options: IPv6 GNU-getopt no-RTC no-DBus no-i18n no-IDN DHCP DHCPv6 no-scripts TFTP no-conntrack ipset no-auth no-DNSSEC no-loop-detect no-inotify
Jan&&1 00:00:11 dnsmasq-dhcp[500]: DHCP, IP range 192.168.1.2 -- 192.168.1.244, lease time 1d
Jan&&1 00:00:11 dnsmasq-dhcp[500]: DHCP, sockets bound exclusively to interface br0
Jan&&1 00:00:11 dnsmasq[500]: read /etc/hosts - 3 addresses
Jan&&1 00:00:11 dnsmasq[500]: read /etc/storage/dnsmasq/hosts - 0 addresses
Jan&&1 00:00:11 dnsmasq-dhcp[500]: read /etc/dnsmasq/dhcp/dhcp-hosts.rc
Jan&&1 00:00:12 kernel: Ralink HW NAT v2.52.0 Module Enabled, FoE Size: 16384
Jan&&1 00:00:12 RT-AC54U: Hardware NAT/Routing: Enabled, IPoE/PPPoE offload [WAN]&-&[LAN/WLAN]
Jan&&1 00:00:12 RT-AC54U: Hardware NAT/Routing: IPv4 UDP flow offload - ON
Jan&&1 00:00:12 RT-AC54U: Hardware NAT/Routing: IPv6 routes offload - OFF
Jan&&1 00:00:13 kernel: br0: port 3(rai0) entered forwarding state
Jan&&1 00:00:13 kernel: br0: port 2(ra0) entered forwarding state
Jan&&1 00:00:13 kernel: br0: port 1(eth2.1) entered forwarding state
Jan&&1 00:00:15 DHCP MAN Client: starting on apcli0 ...
Jan&&1 00:00:15 webui: 稍等后启动相关设置
Jan&&1 00:00:15 QOS: 最大下载2560 KB/S,最大上传256 KB/S
Jan&&1 00:00:15 QOS: QOS没有开启或闪存不足缺模块
Jan&&1 00:00:16 crond[565]: crond (busybox 1.24.1) started, log level 8
Jan&&1 00:00:16 防火墙规则: 脚本完成
Jan&&1 00:00:16 pppd[577]: Plugin rp-pppoe.so loaded.
Jan&&1 00:00:16 pppd[577]: RP-PPPoE plugin version 3.12 compiled against pppd 2.4.7
Jan&&1 00:00:16 pppd[578]: pppd 2.4.7 started by admin, uid 0
Jan&&1 00:00:16 httpd[580]: Server listening port 80 (HTTP).
Jan&&1 00:00:50 dropbear[619]: Running in background
Jan&&1 00:00:50 miniupnpd[623]: version 1.9 starting UPnP-IGD ext if ppp0 BOOTID=
Jan&&1 00:00:50 miniupnpd[623]: HTTP listening on port 39945
Jan&&1 00:00:50 kernel: Netfilter messages via NETLINK v0.30.
Jan&&1 00:00:50 kernel: ip_set: protocol 6
Jan&&1 00:00:51 pppd[578]: Timeout waiting for PADO packets
Jan&&1 00:00:53 kernel: br0: port 3(rai0) entered disabled state
Jan&&1 00:00:53 kernel: device rai0 left promiscuous mode
Jan&&1 00:00:53 kernel: br0: port 3(rai0) entered disabled state
Jan&&1 00:01:00 【script】: 脚本检查更新
Jan&&1 00:01:00 【script】: 脚本不需更新
Jan&&1 00:01:01 自定义脚本0: 脚本完成
Jan&&1 00:01:01 dnsmasq[500]: exiting on receipt of SIGTERM
Jan&&1 00:01:01 dnsmasq[800]: started, version 2.75 cachesize 1024
Jan&&1 00:01:01 dnsmasq[800]: compile time options: IPv6 GNU-getopt no-RTC no-DBus no-i18n no-IDN DHCP DHCPv6 no-scripts TFTP no-conntrack ipset no-auth no-DNSSEC no-loop-detect no-inotify
Jan&&1 00:01:01 dnsmasq-dhcp[800]: DHCP, IP range 192.168.1.2 -- 192.168.1.244, lease time 1d
Jan&&1 00:01:01 dnsmasq-dhcp[800]: DHCP, sockets bound exclusively to interface br0
Jan&&1 00:01:01 dnsmasq[800]: read /etc/hosts - 3 addresses
Jan&&1 00:01:01 dnsmasq[800]: read /etc/storage/dnsmasq/hosts - 0 addresses
Jan&&1 00:01:01 dnsmasq-dhcp[800]: read /etc/dnsmasq/dhcp/dhcp-hosts.rc
Jan&&1 00:01:01 dnsmasq[800]: using nameserver 8.8.8.8#53
Jan&&1 00:01:01 di: 互联网状态：12, 经过时间: ts.
Jan&&1 00:01:01 连接AP: 12秒后，自动搜寻ap
Jan&&1 00:01:13 连接AP: 脚本完成
Jan&&1 00:01:13 sh_download: 下载失败:【/tmp/small_blank.gif】 URL:【】
Jan&&1 00:01:13 sh_download: 重新下载:【/tmp/small_blank.gif】 URL:【】
Jan&&1 00:01:29 sh_download: 下载失败:【/tmp/small_blank.gif】 URL:【】
Jan&&1 00:01:29 自定义脚本: 等待联网后开始脚本
Jan&&1 00:01:29 sh_download: 下载失败:【/tmp/small_blank.gif】 URL:【】
Jan&&1 00:01:29 sh_download: 重新下载:【/tmp/small_blank.gif】 URL:【】
Jan&&1 00:01:45 sh_download: 下载失败:【/tmp/small_blank.gif】 URL:【】
Jan&&1 00:01:45 自定义脚本: 等待联网后开始脚本
Jan&&1 00:01:45 sh_download: 下载失败:【/tmp/small_blank.gif】 URL:【】
Jan&&1 00:01:45 sh_download: 重新下载:【/tmp/small_blank.gif】 URL:【】
Jan&&1 00:02:01 sh_download: 下载失败:【/tmp/small_blank.gif】 URL:【】
Jan&&1 00:02:01 自定义脚本: 等待联网后开始脚本
Jan&&1 00:02:01 sh_download: 下载失败:【/tmp/small_blank.gif】 URL:【】
Jan&&1 00:02:01 sh_download: 重新下载:【/tmp/small_blank.gif】 URL:【】
Jan&&1 00:02:06 pppd[578]: Timeout waiting for PADO packets
Jan&&1 00:02:17 sh_download: 下载失败:【/tmp/small_blank.gif】 URL:【】
Jan&&1 00:02:17 自定义脚本: 等待联网超时
Jan&&1 00:02:31 pppd[578]: recv (receivePacket): Network is down
Jan&&1 00:02:31 kernel: br0: port 2(ra0) entered disabled state
Jan&&1 00:02:33 kernel: br0: port 2(ra0) entered listening state
Jan&&1 00:02:33 pppd[578]: Unable to complete PPPoE Discovery
Jan&&1 00:02:33 pppd[578]: Terminating on signal 15
Jan&&1 00:02:33 pppd[578]: Exit.
Jan&&1 00:02:34 RT-AC54U: Hardware NAT/Routing: Enabled, IPoE/PPPoE offload [WAN]&-&[LAN/WLAN]
Jan&&1 00:02:34 RT-AC54U: Hardware NAT/Routing: IPv4 UDP flow offload - ON
Jan&&1 00:02:34 RT-AC54U: Hardware NAT/Routing: IPv6 routes offload - OFF
Jan&&1 00:02:34 DHCP MAN Client: starting on eth2.2 ...
Jan&&1 00:02:34 QOS: 最大下载2560 KB/S,最大上传256 KB/S
Jan&&1 00:02:34 webui: 稍等后启动相关设置
Jan&&1 00:02:34 QOS: QOS没有开启或闪存不足缺模块
Jan&&1 00:02:34 防火墙规则: 脚本完成
Jan&&1 00:02:34 pppd[1162]: Plugin rp-pppoe.so loaded.
Jan&&1 00:02:34 pppd[1162]: RP-PPPoE plugin version 3.12 compiled against pppd 2.4.7
Jan&&1 00:02:34 pppd[1164]: pppd 2.4.7 started by admin, uid 0
Jan&&1 00:02:34 crond[1166]: crond (busybox 1.24.1) started, log level 8
Jan&&1 00:02:34 pppd[1164]: PPP session is 1 (0x1)
Jan&&1 00:02:34 pppd[1164]: Connected to a0:f3:e4:07:a1:43 via interface eth2.2
Jan&&1 00:02:34 pppd[1164]: Using interface ppp0
Jan&&1 00:02:34 pppd[1164]: Connect: ppp0 &--& eth2.2
Jan&&1 00:02:37 pppd[1164]: Remote message: Accept-03: /service/pppoe
Jan&&1 00:02:37 pppd[1164]: PAP authentication succeeded
Jan&&1 00:02:37 pppd[1164]: peer from calling number A0:F3:E4:07:A1:43 authorized
Jan&&1 00:02:37 pppd[1164]: local&&IP address 183.153.23.64
Jan&&1 00:02:37 pppd[1164]: remote IP address 10.126.128.1
Jan&&1 00:02:37 pppd[1164]: primary& &DNS address 60.191.134.196
Jan&&1 00:02:37 pppd[1164]: secondary DNS address 60.191.134.206
Jan&&1 00:02:37 RT-AC54U: WAN up (ppp0)
Jan&&1 00:02:37 dnsmasq[800]: read /etc/hosts - 3 addresses
Jan&&1 00:02:37 dnsmasq[800]: read /etc/storage/dnsmasq/hosts - 0 addresses
Jan&&1 00:02:37 dnsmasq-dhcp[800]: read /etc/dnsmasq/dhcp/dhcp-hosts.rc
Jan&&1 00:02:37 dnsmasq[800]: using nameserver 60.191.134.196#53
Jan&&1 00:02:37 dnsmasq[800]: using nameserver 60.191.134.206#53
Jan&&1 00:02:38 admin: 运行后WAN上/下活动： WAN动作:【up】，WAN接口名称:【ppp0】
Jan&&1 00:02:38 QOS: 最大下载2560 KB/S,最大上传256 KB/S
Jan&&1 00:02:38 webui: 稍等后启动相关设置
Jan&&1 00:02:38 PPPoE: Connected
Jan&&1 00:02:38 webui: 稍等后启动相关设置
Jan&&1 00:02:38 QOS: QOS没有开启或闪存不足缺模块
Jan&&1 00:02:38 防火墙规则: 脚本完成
Jan&&1 00:02:40 NTP Client: Synchronizing time to .
Mar&&2 07:16:01 NTP Client: System time changed, offset: 547s
Mar&&2 07:16:02 iptables: 删除8118转发规则
Mar&&2 07:16:03 adbyby: 开始下载7620n.tar.gz
Mar&&2 07:16:07 adbyby: 启动adbyby程序
Mar&&2 07:16:08 kernel: br0: port 2(ra0) entered learning state
Mar&&2 07:16:08 【adbyby】: 第一次加载规则完毕
Mar&&2 07:16:08 dnsmasq[800]: exiting on receipt of SIGTERM
Mar&&2 07:16:08 dnsmasq[1362]: started, version 2.75 cachesize 1024
Mar&&2 07:16:08 dnsmasq[1362]: compile time options: IPv6 GNU-getopt no-RTC no-DBus no-i18n no-IDN DHCP DHCPv6 no-scripts TFTP no-conntrack ipset no-auth no-DNSSEC no-loop-detect no-inotify
Mar&&2 07:16:08 dnsmasq-dhcp[1362]: DHCP, IP range 192.168.1.2 -- 192.168.1.244, lease time 1d
Mar&&2 07:16:08 dnsmasq-dhcp[1362]: DHCP, sockets bound exclusively to interface br0
Mar&&2 07:16:08 dnsmasq[1362]: read /etc/hosts - 3 addresses
Mar&&2 07:16:08 dnsmasq[1362]: read /etc/storage/dnsmasq/hosts - 0 addresses
Mar&&2 07:16:08 dnsmasq-dhcp[1362]: read /etc/dnsmasq/dhcp/dhcp-hosts.rc
Mar&&2 07:16:08 dnsmasq[1362]: using nameserver 60.191.134.196#53
Mar&&2 07:16:08 dnsmasq[1362]: using nameserver 60.191.134.206#53
Mar&&2 07:16:10 adbyby: 启动完成
Mar&&2 07:16:10 adbyby: lazy更新：!&&-----����ʱ��:&& 22:35:25& &by:xwhyc-----^M
Mar&&2 07:16:10 adbyby: video更新：!&&-----����ʱ��:&& 22:54:24& &by:xwhyc-----------------------------------------------^M
Mar&&2 07:16:10 adbyby: 第三方规则行数：&&行
Mar&&2 07:16:10 adbyby: 自定义规则行数： 3 行
Mar&&2 07:16:10 adbyby: adbyby 进程守护启动
Mar&&2 07:16:10 自定义脚本: 脚本完成
Mar&&2 07:16:10 adbyby: 找不到8118转发规则，重新添加
Mar&&2 07:16:10 iptables: 添加8118转发规则
Mar&&2 07:16:17 pppd[1164]: System time change detected.
Mar&&2 07:16:20 crond[1166]: time disparity of 613873 minutes detected
Mar&&2 07:16:21 【opt】: opt不需更新
Mar&&2 07:16:21 webui: UI 开关遍历状态监测
Mar&&2 07:16:21 运行路由器启动后: 脚本完成
Mar&&2 07:16:21 自定义脚本0: 脚本完成
Mar&&2 07:16:23 kernel: br0: topology change detected, propagating
Mar&&2 07:16:23 kernel: br0: port 2(ra0) entered forwarding state
Mar&&2 07:16:27 crond[1681]: crond (busybox 1.24.1) started, log level 8
Mar&&2 07:16:27 dnsmasq[1362]: exiting on receipt of SIGTERM
Mar&&2 07:16:27 dnsmasq[1701]: started, version 2.75 cachesize 1024
Mar&&2 07:16:27 dnsmasq[1701]: compile time options: IPv6 GNU-getopt no-RTC no-DBus no-i18n no-IDN DHCP DHCPv6 no-scripts TFTP no-conntrack ipset no-auth no-DNSSEC no-loop-detect no-inotify
Mar&&2 07:16:27 dnsmasq-dhcp[1701]: DHCP, IP range 192.168.1.2 -- 192.168.1.244, lease time 1d
Mar&&2 07:16:27 dnsmasq-dhcp[1701]: DHCP, sockets bound exclusively to interface br0
Mar&&2 07:16:27 dnsmasq[1701]: read /etc/hosts - 3 addresses
Mar&&2 07:16:27 dnsmasq[1701]: read /etc/storage/dnsmasq/hosts - 0 addresses
Mar&&2 07:16:27 dnsmasq-dhcp[1701]: read /etc/dnsmasq/dhcp/dhcp-hosts.rc
Mar&&2 07:16:27 dnsmasq[1701]: using nameserver 60.191.134.196#53
Mar&&2 07:16:27 dnsmasq[1701]: using nameserver 60.191.134.206#53
Mar&&2 07:16:27 SS: 清理防火墙转发规则
Mar&&2 07:16:27 SS: SS service stop.
Mar&&2 07:16:55 kernel: br0: port 2(ra0) entered disabled state
Mar&&2 07:16:57 kernel: br0: port 2(ra0) entered listening state
Mar&&2 07:17:12 kernel: br0: port 2(ra0) entered learning state
Mar&&2 07:17:27 kernel: br0: topology change detected, propagating
Mar&&2 07:17:27 kernel: br0: port 2(ra0) entered forwarding state
求助啊，lz大大！！！我路由器是斐讯psg1208，刷了最新的099，设置好ss，打开了adbyby，一个小时不到，ss和 ...
看样子是你的机内存不够用！不会是64M的吧？
对，64内存，8m闪存，是内存不够的原因吗？&
190 / 624 页
Powered by}