单击进入官方淘宝店，享受多重优惠
随笔 - 163, 文章 - 2, 评论 - 174, 引用 - 0
TFTP 智能刷机从发布以来一直受广大刷机朋友的喜爱，也有很多人一直加我的Q问如何刷机？
在这里我要告诉大家一下，由于机型种类繁多，建议有遇到问题，直接百度，有空的时候我能回答我尽量回答，其他的爱莫能助哦
为什么升级TFTP智能刷机呢？主要有两个原因：
1、最近在帮客户做一个斐讯FIR302B下的智能wifiDog固件，OEM、简单化设置、智能上传设备信息到协成认证中
由于固件制作过程中有可能会出现固件问题，导致无法启动，这个就没有办法更新固件了。（斐讯FIR302B无法使用原有的TFTP直接刷机，这个功能被他们屏蔽啦）
所以只能通过在CFE中，上传固件的方式来刷，也就是救砖
2、上次就有好多个朋友在Q上和我说这个问题，就顺便找个时间来解决了
软件下载地址：
下面我就以斐讯FIR302B来给大家说明一下，救砖咯：
这个FIR302B真的比较变态啦，像其他的BCM5357就没有这么麻烦了，不过这个设备便宜啊，一台才39块钱，超便宜的
1、TTL线会接？（这个型号要自己焊上去，孔有预留），参数是 ，N，1
2、请按住CTRL+C，上电，进入CFE模式。
3、打开TFTP软件
4、选择固件
5、点服务端模式，启动服务端刷机模式，如果本机IP不是你的有线网卡IP，请重新输入，并生成，这个时候他会自动复制到剪切板
6、进入CFE，右键，粘贴，回车
搞定，如果你只是想清除NV，也可以使用nvram erase来清除NV哦。
如果说我没有TTL线，要如何修复呢？这个简单，把本机的IP修改成192.168.1.3，把要刷的固件修改成vmlinuz，启动服务端模式，路由重新上电，会自动刷
要是有不清楚的，可以QQ：联系我，TA的最新馆藏[转]&[转]&[转]&[转]&[转]&[转]&查看: 333|回复: 0
TTL有显示，不知对不对，就是无法刷机？
nf_conntrack version 0.5.0 (3955 buckets, 15820 max)
NETDETECT target register
IPVS: Registered protocols ()
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: ipvs loaded.
ip_nat_bnet: Trying to register for port 6112
ip_tables: (C)
Netfilter Core Team, Type=Linux
TCP cubic registered
Twin IP Module Init
--& Init Smart QoS Monitor
Init SKIP Netfilter
NET: Registered protocol family 17
L2TP core driver, V2.0
L2TP netlink interface
802.1Q VLAN Support v1.8 Ben Greear &&
All bugs added by David S. Miller &&
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
List of all partitions:
1f00& && && &&&16128 mtdblock0 (driver?)
1f01& && && && & 128 mtdblock1 (driver?)
1f02& && && && &&&64 mtdblock2 (driver?)
1f03& && && && &&&64 mtdblock3 (driver?)
1f04& && && && &2176 mtdblock4 (driver?)
1f05& && && &&&13952 mtdblock5 (driver?)
No filesystem could mount root, tried:&&ext3 ext2 ext4 squashfs vfat fuseblk
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,5)
===================================================================
& && && && && & MT7621& &stage1 code 10:33:55 (ASIC)
& && && && && & CPU= HZ BUS= HZ
==================================================================
Change MPLL source from XTAL to CR...
do MEMPLL setting..
MEMPLL Config : 0x
3PLL mode + External loopback
=== XTAL-40Mhz === DDR-1200Mhz ===
PLL4 FB_DL: 0x9, 1/0 = 646/378
PLL2 FB_DL: 0xd, 1/0 = 558/466
PLL3 FB_DL: 0x10, 1/0 = 673/351
do DDR setting..[01F40000]
Apply DDR3 Setting...(use customer AC)
& && && & 0& & 8& &16& &24& &32& &40& &48& &56& &64& &72& &80& &88& &96&&104&&112&&120
& && &--------------------------------------------------------------------------------
0000:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0
0001:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0
0002:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0
0003:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0
0004:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0
0005:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0
0006:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0
0007:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0
0008:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0
0009:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0
000A:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0
000B:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0
000C:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0
000D:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 1
000E:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 1& & 1& & 1& & 1& & 1& & 1& & 1
000F:|& & 0& & 0& & 0& & 0& & 1& & 1& & 1& & 1& & 1& & 1& & 1& & 1& & 1& & 1& & 0& & 0
0010:|& & 1& & 1& & 1& & 1& & 1& & 1& & 1& & 1& & 1& & 0& & 0& & 0& & 0& & 0& & 0& & 0
0011:|& & 1& & 1& & 1& & 1& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0
0012:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0
0013:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0
0014:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0
0015:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0
0016:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0
0017:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0
0018:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0
0019:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0
001A:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0
001B:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0
001C:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0
001D:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0
001E:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0
001F:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0
rank 0 coarse = 15
rank 0 fine = 72
B:|& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 0& & 1& & 1& & 1& & 0& & 0& & 0& & 0& & 0
opt_dle value:9
DRAMC_R0DELDLY[018]=00001E1F
==================================================================
& && && && && & RX& && &DQS perbit delay software calibration
==================================================================
1.0-15 bit dq delay value
==================================================================
bit|& &&&0&&1&&2&&3&&4&&5&&6&&7&&8&&9
--------------------------------------
0 |& & 11 9 9 10 9 9 9 7 6 8
10 |& & 7 11 9 10 6 10
--------------------------------------
==================================================================
2.dqs window
x=pass dqs delay value (min~max)center
y=0-7bit DQ of every group
input delayQS0 =31 DQS1 = 30
==================================================================
bit& &&&DQS0& &&&bit& && &DQS1
0&&(1~59)30&&8&&(0~58)29
1&&(1~58)29&&9&&(1~58)29
2&&(1~58)29&&10&&(1~59)30
3&&(1~58)29&&11&&(1~59)30
4&&(1~59)30&&12&&(1~60)30
5&&(1~61)31&&13&&(1~58)29
6&&(1~60)30&&14&&(1~59)30
7&&(1~62)31&&15&&(1~60)30
==================================================================
3.dq delay value last
==================================================================
bit|& & 0&&1&&2&&3&&4&&5&&6&&7&&8& &9
--------------------------------------
0 |& & 12 11 11 12 10 9 10 7 7 9
10 |& & 7 11 9 11 6 10
==================================================================
==================================================================
& &&&TX&&perbyte calibration
==================================================================
DQS loop = 15, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqsdly_pass[0]=15,&&finish count=1
dqs_perbyte_dly.last_dqsdly_pass[1]=15,&&finish count=2
DQ loop=15, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqdly_pass[0]=15,&&finish count=1
dqs_perbyte_dly.last_dqdly_pass[1]=15,&&finish count=2
byte:0, (DQS,DQ)=(8,8)
byte:1, (DQS,DQ)=(8,8)
20,data:88
[EMI] DRAMC calibration passed
===================================================================
& && && && && & MT7621& &stage1 code done
& && && && && & CPU= HZ BUS= HZ
===================================================================
U-Boot 1.1.3 (Aug 31 2015 - 22:21:15)
Board: Ralink APSoC DRAM:&&256 MB
relocate_code Pointer at: 8ffb8000
Config XHCI 40M PLL
flash manufacture id: ef, device id 40 18
find flash: W25Q128BV
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 4.3.0.0
--------------------------------------------
ASIC MT7621A DualCore (MAC to MT7530 Mode)
DRAM_CONF_FROM: Auto-Detection
DRAM_TYPE: DDR3
DRAM bus: 16 bit
Xtal Mode=3 OCP Ratio=1/3
Flash component: SPI Flash
Date:Aug 31 2015&&Time:22:21:15
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 880 MHZ ####
estimate memory size =256 Mbytes
#Reset_MT7530
Please choose the operation:
& &1: Load system code to SDRAM via TFTP.
& &2: Load system code then write to Flash via TFTP.
& &3: Boot system code via Flash (default).
& &4: Entr boot command line interface.
& &6: Load Flash code then burn to Flash via TFTP.
& &7: Load Boot Loader code then write to Flash via Serial.
& &9: Load Boot Loader code then write to Flash via TFTP.
You choosed 3
3: System Boot system code via Flash.
## Booting image at bfc50000 ...
& &Image Name:& &za3nd
& &Image Type:& &MIPS Linux Kernel Image (lzma compressed)
& &Data Size:& &
Bytes = 11 MB
& &Load Address:
& &Entry Point:&&
& &Verifying Checksum ... OK
& &Uncompressing Kernel Image ... OK
## Transferring control to Linux (at address ) ...
## Giving linux memsize in MB, 256
Starting kernel ...
LINUX started...
THIS IS ASIC
Linux version 2.6.36 () (gcc version 4.6.3 (Buildroot ) ) #111 SMP Mon Nov 23 17:27:03 KST 2015
The CPU feqenuce set to 880 MHz
GCMP present
CPU revision is: 0001992f (MIPS 1004Kc)
Software DMA cache coherency
Determined physical RAM map:
Initrd not found or empty - disabling initrd
Zone PFN ranges:
&&Normal& &0x -& 0x
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
& & 0: 0x -& 0x
Detected 3 available secondary CPU(s)
PERCPU: Embedded 7 pages/cpu @12 r u65536
pcpu-alloc: s d1 alloc=16*4096
pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
Built 1 zonelists in Zone order, mobility grouping on.&&Total pages: 65024
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5 console=ttyS0
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Writing ErrCtl register=0004021f
Readback ErrCtl register=0004021f
Memory: 2144k available (4662k kernel code, 8976k reserved, 1367k data, 216k init, 0k highmem)
Hierarchical RCU implementation.
& && &&&Verbose stalled-CPUs detection is disabled.
NR_IRQS:128
Trying to install interrupt handler for IRQ24
Trying to install interrupt handler for IRQ25
Trying to install interrupt handler for IRQ22
Trying to install interrupt handler for IRQ9
Trying to install interrupt handler for IRQ10
Trying to install interrupt handler for IRQ11
Trying to install interrupt handler for IRQ12
Trying to install interrupt handler for IRQ13
Trying to install interrupt handler for IRQ14
Trying to install interrupt handler for IRQ16
Trying to install interrupt handler for IRQ17
Trying to install interrupt handler for IRQ18
Trying to install interrupt handler for IRQ19
Trying to install interrupt handler for IRQ20
Trying to install interrupt handler for IRQ21
Trying to install interrupt handler for IRQ23
Trying to install interrupt handler for IRQ26
Trying to install interrupt handler for IRQ27
Trying to install interrupt handler for IRQ28
Trying to install interrupt handler for IRQ15
Trying to install interrupt handler for IRQ8
Trying to install interrupt handler for IRQ29
Trying to install interrupt handler for IRQ30
Trying to install interrupt handler for IRQ31
console [ttyS1] enabled
Calibrating delay loop... 577.53 BogoMIPS (lpj=1155072)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
launch: starting cpu1
launch: cpu1 gone!
CPU revision is: 0001992f (MIPS 1004Kc)
Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
launch: starting cpu2
launch: cpu2 gone!
CPU revision is: 0001992f (MIPS 1004Kc)
Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
launch: starting cpu3
launch: cpu3 gone!
CPU revision is: 0001992f (MIPS 1004Kc)
Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Brought up 4 CPUs
Synchronize counters across 4 CPUs: done.
NET: Registered protocol family 16
release PCIe RST: RALINK_RSTCTRL = 7000000
PCIE PHY initialize
***** Xtal 40MHz *****
start MT7621 PCIe register access
RALINK_RSTCTRL = 7000000
RALINK_CLKCFG1 = 77ffeff8
*************** MT7621 PCIe RC mode *************
PCIE2 no card, disable it(RST&CLK)
pcie_link status = 0x3
RALINK_RSTCTRL= 3000000
*** Configure Device number setting of Virtual PCI-PCI bridge ***
RALINK_PCI_PCICFG_ADDR = 21007f2 -& 21007f2
PCIE0 enabled
PCIE1 enabled
interrupt enable status: 300000
Port 1 N_FTS = 1b105000
Port 0 N_FTS = 1b105000
config reg done
init_rt2880pci done
bio: create slab &bio-0& at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci .0: BAR 0: can't assign mem (size 0x)
pci .0: BAR 0: can't assign mem (size 0x)
pci .0: BAR 8: assigned [mem 0xx600fffff]
pci .0: BAR 9: assigned [mem 0xx601fffff pref]
pci .0: BAR 8: assigned [mem 0xx602fffff]
pci .0: BAR 9: assigned [mem 0xx603fffff pref]
pci .0: BAR 1: assigned [mem 0xx6040ffff]
pci .0: BAR 1: set to [mem 0xx6040ffff] (PCI address [0xx6040ffff]
pci .0: BAR 1: assigned [mem 0xx6041ffff]
pci .0: BAR 1: set to [mem 0xx6041ffff] (PCI address [0xx6041ffff]
pci .0: BAR 0: assigned [mem 0xx600fffff 64bit]
pci .0: BAR 0: set to [mem 0xx600fffff 64bit] (PCI address [0xx600fffff]
pci .0: BAR 6: assigned [mem 0xx6010ffff pref]
pci .0: PCI bridge to [bus 01-01]
pci .0:& &bridge window [io&&disabled]
pci .0:& &bridge window [mem 0xx600fffff]
pci .0:& &bridge window [mem 0xx601fffff pref]
pci .0: BAR 0: assigned [mem 0xx602fffff 64bit]
pci .0: BAR 0: set to [mem 0xx602fffff 64bit] (PCI address [0xx602fffff]
pci .0: BAR 6: assigned [mem 0xx6030ffff pref]
pci .0: PCI bridge to [bus 02-02]
pci .0:& &bridge window [io&&disabled]
pci .0:& &bridge window [mem 0xx602fffff]
pci .0:& &bridge window [mem 0xx603fffff pref]
PCI: Enabling device .0 (0004 -& 0006)
PCI: Enabling device .0 (0004 -& 0006)
BAR0 at slot 0 = 0
bus=0x0, slot = 0x0
res[0]-&start = 0
res[0]-&end = 0
res[1]-&start =
res[1]-&end = 6040ffff
res[2]-&start = 0
res[2]-&end = 0
res[3]-&start = 0
res[3]-&end = 0
res[4]-&start = 0
res[4]-&end = 0
res[5]-&start = 0
res[5]-&end = 0
BAR0 at slot 1 = 0
bus=0x0, slot = 0x1
res[0]-&start = 0
res[0]-&end = 0
res[1]-&start =
res[1]-&end = 6041ffff
res[2]-&start = 0
res[2]-&end = 0
res[3]-&start = 0
res[3]-&end = 0
res[4]-&start = 0
res[4]-&end = 0
res[5]-&start = 0
res[5]-&end = 0
bus=0x1, slot = 0x0, irq=0x4
res[0]-&start =
res[0]-&end = 600fffff
res[1]-&start = 0
res[1]-&end = 0
res[2]-&start = 0
res[2]-&end = 0
res[3]-&start = 0
res[3]-&end = 0
res[4]-&start = 0
res[4]-&end = 0
res[5]-&start = 0
res[5]-&end = 0
bus=0x2, slot = 0x1, irq=0x18
res[0]-&start =
res[0]-&end = 602fffff
res[1]-&start = 0
res[1]-&end = 0
res[2]-&start = 0
res[2]-&end = 0
res[3]-&start = 0
res[3]-&end = 0
res[4]-&start = 0
res[4]-&end = 0
res[5]-&start = 0
res[5]-&end = 0
Switching to clocksource MIPS
NET: Registered protocol family 2
--&&&ipconflict proc OK !!!!!!!!!!
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 128 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
NET: Registered protocol family 1
4 CPUs re-calibrate udelay(lpj = 1167360)
squashfs: version 3.2-r2 () Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
fuse init (API version 7.15)
msgmni has been set to 494
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
Ralink gpio driver initialized
spidrv_major = 217
driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A
serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A
brd: module loaded
flash manufacture id: ef, device id 40 18
W25Q128BV(ef ) (16384 Kbytes)
mtd .name = raspi, .size = 0xM) .erasesize = 0xK) .numeraseregions = 0
Creating 6 MTD partitions on &raspi&:
0x-0x : &Firmware&
0x-0x : &Bootloader&
0x-0x : &Config&
0x-0x : &Factory&
0x-0x : &Kernel&
0x-0x : &RootFS&
rdm_major = 253
GMAC1_MAC_ADRH -- : 0x0000000c
GMAC1_MAC_ADRL -- : 0x432880ed
Ralink APSoC Ethernet Driver Initilization. v3.1&&512 rx/tx descriptors allocated, mtu = 1500!
GMAC1_MAC_ADRH -- : 0x0000000c
GMAC1_MAC_ADRL -- : 0x
PROC INIT OK!
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver cdc_eem
usbcore: registered new interface driver rndis_host
usbcore: registered new interface driver cdc_subset
register rt2860
=== pAd = c0182000, size = 2135856 ===
&-- RTMPAllocTxRxRingMemory, Status=0
&-- RTMPAllocAdapterBlock, Status=0
pAd-&CSRBaseAddress =0xc0080000, csr_addr=0xc0080000!
device_id =0x7662
==&rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd-&WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a
RtmpOSFileOpen(): Error 2 opening /etc/Wireless/iNIC/iNIC_ap.dat
Open file &/etc/Wireless/iNIC/iNIC_ap.dat& failed!
###########################################
###########################################
Read Parameters from default_profile_buffer
###########################################
###########################################
mbss& fatal error! beacon offset is error in driver! Please re-assign HW_BEACON_OFFSET!
RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5
RtmpEepromGetDefault::e2p_dafault=2
NVM is efuse and the information is too less to bring up the interface
Force to use Flash mode
NVM is FLASH mode (pAd-&flash_offset = 0x48000)
get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai
=== pAd = c0502000, size = 2135856 ===
&-- RTMPAllocTxRxRingMemory, Status=0
&-- RTMPAllocAdapterBlock, Status=0
pAd-&CSRBaseAddress =0xc0400000, csr_addr=0xc0400000!
device_id =0x7662
==&rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd-&WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a
RtmpOSFileOpen(): Error 2 opening /etc/Wireless/RT2860/RT2860.dat
Open file &/etc/Wireless/RT2860/RT2860.dat& failed!
###########################################
###########################################
Read Parameters from default_profile_buffer
###########################################
###########################################
mbss& fatal error! beacon offset is error in driver! Please re-assign HW_BEACON_OFFSET!
RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5
RtmpEepromGetDefault::e2p_dafault=2
NVM is efuse and the information is too less to bring up the interface
Force to use Flash mode
NVM is FLASH mode (pAd-&flash_offset = 0x40000)
get_dev_name_prefix(): dev_idx = 0, dev_name_prefix=ra
FM_OUT value: u4FmOut = 0(0x)
FM_OUT value: u4FmOut = 0(0x)
FM_OUT value: u4FmOut = 0(0x)
FM_OUT value: u4FmOut = 0(0x)
FM_OUT value: u4FmOut = 0(0x)
FM_OUT value: u4FmOut = 0(0x)
FM_OUT value: u4FmOut = 0(0x)
FM_OUT value: u4FmOut = 0(0x)
FM_OUT value: u4FmOut = 0(0x)
FM_OUT value: u4FmOut = 0(0x)
FM_OUT value: u4FmOut = 0(0x)
FM_OUT value: u4FmOut = 0(0x)
FM_OUT value: u4FmOut = 0(0x)
FM_OUT value: u4FmOut = 0(0x)
FM_OUT value: u4FmOut = 0(0x)
FM_OUT value: u4FmOut = 0(0x)
FM_OUT value: u4FmOut = 0(0x)
FM_OUT value: u4FmOut = 0(0x)
FM_OUT value: u4FmOut = 0(0x)
FM_OUT value: u4FmOut = 0(0x)
xhc_mtk xhc_mtk: xHCI Host Controller
xhc_mtk xhc_mtk: new USB bus registered, assigned bus number 1
xhc_mtk xhc_mtk: irq 22, io mem 0x1e1c0000
------------& USB3.0 is Disabled
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
xhc_mtk xhc_mtk: xHCI Host Controller
xhc_mtk xhc_mtk: new USB bus registered, assigned bus number 2
------------& USB3.0 is Disabled
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i8042.c: i8042 controller self test timeout.
Trying to free nonexistent resource &f&
MTK MSDC device init.
msdc0 -& ops_get_cd return&0& &- msdc_ops_get_cd() : L&2317& PID&kworker/u:1&&0x28&
mtk-sd: MediaTek MT6575 MSDC Driver
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (3955 buckets, 15820 max)
NETDETECT target register
IPVS: Registered protocols ()
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: ipvs loaded.
ip_nat_bnet: Trying to register for port 6112
ip_tables: (C)
Netfilter Core Team, Type=Linux
TCP cubic registered
Twin IP Module Init
--& Init Smart QoS Monitor
Init SKIP Netfilter
NET: Registered protocol family 17
L2TP core driver, V2.0
L2TP netlink interface
802.1Q VLAN Support v1.8 Ben Greear &&
All bugs added by David S. Miller &&
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
List of all partitions:
1f00& && && &&&16128 mtdblock0 (driver?)
1f01& && && && & 128 mtdblock1 (driver?)
1f02& && && && &&&64 mtdblock2 (driver?)
1f03& && && && &&&64 mtdblock3 (driver?)
1f04& && && && &2176 mtdblock4 (driver?)
1f05& && && &&&13952 mtdblock5 (driver?)
No filesystem could mount root, tried:&&ext3 ext2 ext4 squashfs vfat fuseblk
Powered by}