TP-LINK TL-WDR6500 高清拆解 - N多网络设备、高端电脑配件、数码产品拆解 -
恩山无线论坛 -
Powered by Discuz!
后使用快捷导航没有帐号？
只需一步，快速开始
请完成以下验证码
请完成以下验证码
查看: 93988|回复: 38
TP-LINK TL-WDR6500 高清拆解
本帖最后由 hackpascal 于
18:55 编辑
楼主在某宝上入了个转卖的 WDR6500，准备拿来研究
CPU： Qualcomm Atheros QCA9561-AL3A
5G 11ac 无线： Qualcomm Atheros QCA9882-BR4A
频率： CPU 775MHz，DDR 650MHz，AHB 258MHz
内存： EtronTech EM68C16CWQD-25H 128MB DDR2
Flash： Winbond W25Q64FV 8MB
有线网：百兆 4+1，网口8针，指示灯在网口上
其它接口：UART JTAG USB (有焊点引出)
由于固件头变了（看看内核的 mtdparts 就知道），所以没有任何办法可以免拆机刷第三方固件
上图：（图较大，平均 900KB）
1. 外观.jpg (275.84 KB, 下载次数: 11)
18:25 上传
2. 底面.jpg (343.23 KB, 下载次数: 8)
18:25 上传
3. 网口.jpg (227.33 KB, 下载次数: 6)
18:25 上传
4. PCB 正面.jpg (354.78 KB, 下载次数: 45)
18:25 上传
5. PCB 背面.jpg (383.53 KB, 下载次数: 12)
18:25 上传
6. QCA9561.jpg (510.53 KB, 下载次数: 10)
18:25 上传
7. 内存.jpg (392.77 KB, 下载次数: 11)
18:25 上传
8. 2.4G 射频.jpg (458.55 KB, 下载次数: 6)
18:25 上传
9. QCA9882.jpg (508.82 KB, 下载次数: 7)
18:25 上传
10. 5G 射频.jpg (432.39 KB, 下载次数: 8)
18:25 上传
11. 闪存.jpg (374 KB, 下载次数: 7)
18:25 上传
12. UART JTAG.jpg (300.93 KB, 下载次数: 7)
18:25 上传
U-Boot 1.1.4-g5e4af5a2 (Sep 17 2014 - 17:29:36)
ap151 - Dragonfly 1.0
DRAM:&&128 MB Top of RAM usable for U-Boot at:
Reserving 135k for U-Boot at: 87fdc000 Reserving 192k for malloc() at: 87fac000 Reserving 44 Bytes for Board Info at: 87fabfd4 Reserving 36 Bytes for Global Data at: 87fabfb0 Reserving 128k for boot params() at: 87f8bfb0 Stack Pointer at: 87f8bf98 Now running in RAM - U-Boot at: 87fdc000 Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x17 flash size 8MB, sector count = 128 Flash:&&8 MB Using default environment
In:& & serial Out:& &serial Err:& &serial Net:& &ath_gmac_enet_initialize... No valid address in Flash. Using fixed address No valid address in Flash. Using fixed address ath_gmac_enet_initialize: reset mask:c02200 Dragonfly----& S27 PHY * : cfg1 0x cfg2 0x7114 eth0: 00:03:7f:09:0b:ad athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000 athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10 eth0 up ATHRS27: resetting s27 ATHRS27: s27 reset done : cfg1 0x800c0000 cfg2 0x7214 eth1: 00:03:7f:09:0b:ad athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000 athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10 athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000 athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10 athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000 athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10 athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000 athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10 eth1 up eth0, eth1 Setting 0x to 0x82 Hit any key to stop autoboot:&&0 ## Booting image at 9f010200 ... & &Image Name:& &Linux Kernel Image & &Created:& && && &9:29:29 UTC & &Image Type:& &MIPS Linux Kernel Image (lzma compressed) & &Data Size:& & 996298 Bytes = 972.9 kB & &Load Address:
& &Entry Point:&&8020ed90 & &Verifying Checksum at 0x9f010240 ...OK & &Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 8020ed90) ... ## Giving linux memsize in bytes,
Starting kernel ...
Booting QCA956x [& & 0.000000] Linux version 2.6.31--LSDK- () (gcc version 4.3.3 (GCC) ) #1 Wed Sep 17 17:28:37 CST 2014 [& & 0.000000] flash_size passed from bootloader = 8 [& & 0.000000] arg 1: console=ttyS0,115200 [& & 0.000000] arg 2: root=31:03 [& & 0.000000] arg 3: rootfstype=squashfs [& & 0.000000] arg 4: init=/sbin/init [& & 0.000000] arg 5: mtdparts=ath-nor0:32k(u-boot),32k(u-boot-env),1024k(uImage),6976k(rootfs),64k(mib0),64k(ART) [& & 0.000000] arg 6: mem=128M [& & 0.000000] CPU revision is:
(MIPS 74Kc) [& & 0.000000] ath_sys_frequency: cpu 775 ddr 650 ahb 258 [& & 0.000000] Determined physical RAM map: [& & 0.000000]&&memory:
(usable) [& & 0.000000] User-defined physical RAM map: [& & 0.000000]&&memory:
(usable) [& & 0.000000] Initrd not found or empty - disabling initrd [& & 0.000000] Zone PFN ranges: [& & 0.000000]& &Normal& &0x -& 0x [& & 0.000000] Movable zone start PFN for each node [& & 0.000000] early_node_map[1] active PFN ranges [& & 0.000000]& &&&0: 0x -& 0x [& & 0.000000] Built 1 zonelists in Zone order, mobility grouping on.&&Total pages: 32512 [& & 0.000000] Kernel command line: console=ttyS0,115200 root=31:03 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:32k(u-boot),32k(u-boot-env),1024k(uImage),6976k(rootfs),64k(mib0),64k(ART) mem=128M [& & 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes) [& & 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [& & 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [& & 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [& & 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [& & 0.000000] Writing ErrCtl register= [& & 0.000000] Readback ErrCtl register= [& & 0.000000] Memory: 1072k available (2117k kernel code, 18392k reserved, 520k data, 160k init, 0k highmem) [& & 0.000000] NR_IRQS:128 [& & 0.000000] plat_time_init: plat time init done [& & 0.000000] r4k_clockevent_init: Ignoring int_usable failure [& & 0.000000] Console: colour dummy device 80x25 [& & 0.000000] Calibrating delay loop... 387.07 BogoMIPS (lpj=774144) [& & 0.080000] Mount-cache hash table entries: 512 [& & 0.080000] [& & 0.080000] ****************ALLOC*********************** [& & 0.080000]&&Packet mem: 802d000 bytes) [& & 0.080000] ******************************************** [& & 0.080000] [& & 0.080000] NET: Registered protocol family 16 [& & 0.080000] ath_pcibios_init: bus 0 [& & 0.080000] ath_pcibios_init(255): PCI 0 CMD write: 0x356 [& & 0.080000] registering PCI controller with io_map_base unset [& & 0.080000] bio: create slab &bio-0& at 0 [& & 0.080000] SCSI subsystem initialized [& & 0.080000] pci .0: PME# supported from D0 D1 D3hot [& & 0.080000] pci .0: PME# disabled [& & 0.080000] pcibios_map_irq: IRQ 76 for bus 0 [& & 0.080000] NET: Registered protocol family 2 [& & 0.080000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [& & 0.080000] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [& & 0.080000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [& & 0.080000] TCP: Hash tables configured (established 4096 bind 4096) [& & 0.084000] TCP reno registered [& & 0.084000] NET: Registered protocol family 1 [& & 0.084000] ATH GPIOC major 0 [& & 0.084000] squashfs: version 4.0 () Phillip Lougher [& & 0.084000] JFFS2 version 2.2 (NAND) (ZLIB) (RTIME) (c)
Red Hat, Inc. [& & 0.084000] fuse init (API version 7.12) [& & 0.084000] msgmni has been set to 220 [& & 0.084000] io scheduler noop registered [& & 0.084000] io scheduler deadline registered (default) [& & 0.088000] Serial:
driver, 1 ports, IRQ sharing disabled [& & 0.088000] serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A [& & 0.088000] console [ttyS0] enabled [& & 0.448000] brd: module loaded [& & 0.452000] PPP generic driver version 2.4.2 [& & 0.456000] NET: Registered protocol family 24 [& & 0. cmdlinepart partitions found on MTD device ath-nor0 [& & 0.468000] Creating 6 MTD partitions on &ath-nor0&: [& & 0.x-0x : &u-boot& [& & 0.480000] mtd: partition &u-boot& doesn't end on an erase block -- force read-only [& & 0.x-0x : &u-boot-env& [& & 0.492000] mtd: partition &u-boot-env& doesn't start on an erase block boundary -- force read-only [& & 0.x-0x : &uImage& [& & 0.x-0x0 : &rootfs& [& & 0.x0-0x0 : &mib0& [& & 0.x0-0x : &ART& [& & 0.524000] -&Oops: flash id 0xef4017 . [& & 0.528000] ----TP IGMP has been init------ [& & 0.532000] TCP cubic registered [& & 0.536000] NET: Registered protocol family 10 [& & 0.540000] NET: Registered protocol family 17 [& & 0.2.1Q VLAN Support v1.8 Ben Greear && [& & 0.552000] All bugs added by David S. Miller && [& & 0.556000] athwdt_init: Registering WDT success [& & 0.568000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. [& & 0.576000] Freeing unused kernel memory: 160k freed init started: BusyBox v1.21.1 ( 17:32:50 CST) [& & 1.316000] usbcore: registered new interface driver usbfs [& & 1.324000] usbcore: registered new interface driver hub [& & 1.328000] usbcore: registered new device driver usb [& & 1.396000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [& & 1.404000] Port Status 1c000004 [& & 1.404000] ath-ehci ath-ehci.0: ATH EHCI [& & 1.408000] ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1 [& & 1.420000] ehci_reset Intialize USB CONTROLLER in host mode: 13 [& & 1.424000] ehci_reset Port Status 1c000000 [& & 1.428000] ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000 [& & 1.436000] ehci_reset Intialize USB CONTROLLER in host mode: 13 [& & 1.444000] ehci_reset Port Status 1c000000 [& & 1.460000] ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00 [& & 1.464000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [& & 1.472000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [& & 1.480000] usb usb1: Product: ATH EHCI [& & 1.484000] usb usb1: Manufacturer: Linux 2.6.31--LSDK- ehci_hcd [& & 1.488000] usb usb1: SerialNumber: platform [& & 1.492000] usb usb1: configuration #1 chosen from 1 choice [& & 1.500000] hub 1-0:1.0: USB hub found [& & 1.504000] hub 1-0:1.0: 1 port detected [& & 1.508000] Port Status 1c000000 [& & 1.512000] ath-ehci1 ath-ehci1.1: ATH EHCI [& & 1.516000] ath-ehci1 ath-ehci1.1: new USB bus registered, assigned bus number 2 [& & 1.524000] ehci_reset Intialize USB CONTROLLER in host mode: 13 [& & 1.532000] ehci_reset Port Status 1c000000 [& & 1.536000] ath-ehci1 ath-ehci1.1: irq 3, io mem 0x1b400000 [& & 1.544000] ehci_reset Intialize USB CONTROLLER in host mode: 13 [& & 1.552000] ehci_reset Port Status 1c000000 [& & 1.568000] ath-ehci1 ath-ehci1.1: USB 2.0 started, EHCI 1.00 [& & 1.572000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [& & 1.580000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [& & 1.588000] usb usb2: Product: ATH EHCI [& & 1.592000] usb usb2: Manufacturer: Linux 2.6.31--LSDK- ehci_hcd [& & 1.596000] usb usb2: SerialNumber: platform [& & 1.604000] usb usb2: configuration #1 chosen from 1 choice [& & 1.608000] hub 2-0:1.0: USB hub found [& & 1.612000] hub 2-0:1.0: 1 port detected [& & 1.676000] Initializing USB Mass Storage driver... [& & 1.680000] usbcore: registered new interface driver usb-storage [& & 1.688000] USB Mass Storage support registered. [& & 1.760000] usbcore: registered new interface driver cdc_ether This Board use 2.6.31 [& & 1.876000] xt_time: kernel timezone is -0000 [& & 1.996000] nf_conntrack version 0.5.0 (2048 buckets, 32768 max) [& & 2.256000] ip_tables: (C)
Netfilter Core Team insmod: can't insert '/lib/modules/2.6.31/kernel/iptable_raw.ko': No such file or directory insmod: can't insert '/lib/modules/2.6.31/kernel/flashid.ko': No such file or directory insmod: can't insert '/lib/modules/2.6.31/kernel/br_filter.ko': No such file or directory [& & 2.464000] PPPoL2TP kernel driver, V1.0 [& & 2.500000] PPTP driver version 0.8.3 insmod: can't insert '/lib/modules/2.6.31/kernel/harmony.ko': No such file or directory
(none) mips #1 Wed Sep 17 17:28:37 CST 2014 (none) (none) login: [& & 3.128000] Now flash open! [& & 3.284000] qca956x_GMAC: Length per segment 1536 [& & 3.6x_GMAC: qca956x_gmac_attach [& & 3.6x_GMAC: qca956x_set_gmac_caps [& & 3.296000] GPIO LED SETTINGS ....done [& & 3.300000] Currently in interrupt mode unit1 [& & 3.304000] qca956x_set_gmac_caps& & CHECK DMA STATUS [& & 3.312000] mac:1 Registering S27.... [& & 3.316000] qca956x_GMAC: RX TASKLET - Pkts per Intr:32 [& & 3.320000] qca956x_GMAC: Mac address for unit 1:bfff0006 [& & 3.324000] qca956x_GMAC: ff:ff:ff:ff:ff:ff [& & 3.332000] qca956x_GMAC: Max segments per packet :& &1 [& & 3.336000] qca956x_GMAC: Max tx descriptor count :& &128 [& & 3.340000] qca956x_GMAC: Max rx descriptor count :& &128 [& & 3.348000] qca956x_GMAC: Mac capability flags& & :& &2401 [& & 3.6x_GMAC: qca956x_gmac_attach [& & 3.6x_GMAC: qca956x_set_gmac_caps [& & 3.360000] Currently in interrupt mode unit0 [& & 3.364000] qca956x_set_gmac_caps& & CHECK DMA STATUS [& & 3.372000] mac:0 Registering S27.... [& & 3.376000] qca956x_GMAC: RX TASKLET - Pkts per Intr:32 [& & 3.380000] qca956x_GMAC: Mac address for unit 0:bfff0000 [& & 3.384000] qca956x_GMAC: ff:ff:ff:ff:ff:ff [& & 3.392000] qca956x_GMAC: Max segments per packet :& &1 [& & 3.396000] qca956x_GMAC: Max tx descriptor count :& &128 [& & 3.400000] qca956x_GMAC: Max rx descriptor count :& &128 [& & 3.408000] qca956x_GMAC: Mac capability flags& & :& &2401 [& & 4.020000] athr_gmac_ring_alloc Allocated 2048 at 0x87b3a800 [& & 4.028000] sram_desc_cnt 1536,mac Unit 0,Tx r-&ring_desc 0xbd000000 [& & 4.036000] athr_gmac_ring_alloc Allocated 2048 at 0x87b3a000 [& & 4.040000] sram_desc_cnt 3072,mac Unit 0,Rx r-&ring_desc 0xbd000600 [& & 4.6x_GMAC: eth0 in MII MODE [& & 4.352000] Dragonfly -----& S27 PHY [& & 4.356000] Setting Drop CRC Errors, Pause Frames and Length Error frames [& & 4.372000] Setting PHY... [& & 4.696000] ADDRCONF(NETDEV_UP): eth1: link is not ready [& & 4.708000] athr_gmac_ring_alloc Allocated 2048 at 0x87b3b800 [& & 4.716000] sram_desc_cnt 4608,mac Unit 1,Tx r-&ring_desc 0xbd000c00 [& & 4.720000] athr_gmac_ring_alloc Allocated 2048 at 0x87b3b000 [& & 4.728000] sram_desc_cnt 6144,mac Unit 1,Rx r-&ring_desc 0xbd001200 [& & 5.6x_GMAC: eth1 in RGMII MODE [& & 5.036000] Dragonfly -----& S27 PHY [& & 5.040000] ATHRS27: resetting s27 [& & 5.144000] ATHRS27: s27 reset done [& & 5.160000] ++++ athrs27_igmp_setup once [& & 5.172000] Setting Drop CRC Errors, Pause Frames and Length Error frames [& & 5.188000] Setting PHY... [& & 5.316000] ADDRCONF(NETDEV_UP): eth0: link is not ready [& & 5.336000] device eth0 entered promiscuous mode [& & 5.348000] Now flash open! [& & 5.356000] athr_gmac_ring_free Freeing at 0x87b3a800 [& & 5.356000] athr_gmac_ring_free Freeing at 0x87b3a000 [& & 5.380000] athr_gmac_ring_alloc Allocated 2048 at 0x87b3a000 [& & 5.388000] sram_desc_cnt 6144,mac Unit 0,Tx r-&ring_desc 0xbd000000 [& & 5.396000] athr_gmac_ring_alloc Allocated 2048 at 0x87b3a800 [& & 5.400000] sram_desc_cnt 6144,mac Unit 0,Rx r-&ring_desc 0xbd000600 [& & 5.6x_GMAC: eth0 in MII MODE [& & 5.712000] Dragonfly -----& S27 PHY [& & 5.716000] Setting Drop CRC Errors, Pause Frames and Length Error frames [& & 5.732000] Setting PHY... [& & 6.056000] ADDRCONF(NETDEV_UP): eth1: link is not ready route: SIOCADDRT: Invalid argument [& & 6.072000] athr_gmac_ring_free Freeing at 0x87b3b800 [& & 6.072000] athr_gmac_ring_free Freeing at 0x87b3b000 [& & 6.100000] athr_gmac_ring_alloc Allocated 2048 at 0x87b3b000 [& & 6.104000] sram_desc_cnt 6144,mac Unit 1,Tx r-&ring_desc 0xbd000c00 [& & 6.112000] athr_gmac_ring_alloc Allocated 2048 at 0x87b3b800 [& & 6.120000] sram_desc_cnt 6144,mac Unit 1,Rx r-&ring_desc 0xbd001200 [& & 6.6x_GMAC: eth1 in RGMII MODE [& & 6.428000] Dragonfly -----& S27 PHY [& & 6.432000] Setting Drop CRC Errors, Pause Frames and Length Error frames [& & 6.452000] Setting PHY... [& & 6.576000] ADDRCONF(NETDEV_UP): eth0: link is not ready route: SIOCADDRT: Invalid argument &wlanWarn& Weak wlanWarn check rmmod: can't unload 'tp_domain': unknown symbol in module, or unknown parameter info, udhcpc (v0.9.9-pre) started info, udhcpd (v0.9.9-pre) started insmod: can't insert '/lib/modules/2.6.31/kernel/nf_conntrack_proto_gre.ko': File exists insmod: can't insert '/lib/modules/2.6.31/kernel/nf_nat_h323.ko': File exists [& & 7.644000] nf_conntrack_rtsp v0.6.21 loading [& & 7.660000] nf_nat_rtsp v0.6.21 loading
[& & 7.764000] adf: module license 'Proprietary' taints kernel. [& & 7.768000] Disabling lock debugging due to kernel taint [& & 8.188000] ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, TX_DATA_SWAP, RX_DATA_SWAP, 11D) [& & 8.252000] ath_rate_atheros: Copyright (c)
Atheros Communications, Inc, All Rights Reserved [& & 8.320000] ath_dfs: Version 2.0.0 [& & 8.320000] Copyright (c)
Atheros Communications, Inc. All Rights Reserved [& & 8.344000] ath_tx99: Version 2.0 [& & 8.344000] Copyright (c) 2010 Atheros Communications, Inc, All Rights Reserved [& & 8.608000] ath_dev: Copyright (c)
Atheros Communications, Inc, All Rights Reserved [& &10.088000] ath_ahb:&&(Atheros/multi-bss) [& &10.096000] __ath_attach: Set global_scn[0] [& &10.108000] Enterprise mode: 0x03bda000 [& &10.112000] Restoring Cal data from Flash [& &10.120000] Green-AP : Green-AP : Attached [& &10.120000] [& &10.128000] ath_get_caps[6128] rx chainmask mismatch actual 7 sc_chainmak 0 [& &10.136000] ath_get_caps[6103] tx chainmask mismatch actual 7 sc_chainmak 0 [& &10.148000] ath_attach_dfs[12518] dfsdomain 1 [& &10.172000] SC Callback Registration for wifi0 [& &10.176000] wifi0: Atheros 956X: mem=0xb8100000, irq=2 [& &10.180000] ath_pci:&&(Atheros/multi-bss) [& &10.184000] ath_pci_probe [& &10.188000] PCI device id is 003c :003c [& &10.196000] ath_pci .0: ath DEBUG: sc=0x86f02e00 [& &10.200000] [& &10.200000]&&ol_ath_pci_configure : num_desired MSI set to 0 [& &10.208000] [& &10.208000]&&Using PCI Legacy Interrupt [& &10.620000] __ol_ath_attach: ath_attach TODO [& &10.628000] __ol_ath_attach: dev name wifi1 [& &10.632000] ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) [& &10.640000]&&OL_ACBKMinfree : 0 [& &10.644000]&&OL_ACBEMinfree : 0 [& &10.648000]&&OL_ACVIMinfree : 0 [& &10.652000]&&OL_ACVOMinfree : 0 [& &10.652000] ol_ath_attach() BMI inited. [& &10.660000] ol_ath_attach() BMI Get Target Info. [& &10.664000] ol_ath_attach() TARGET TYPE: 7 Vers 0x4100016c [& &10.668000] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 [& &10.676000] ol_ath_attach() configure Target . [& &10.680000] qc98xx_verify_checksum: flash checksum passed: 0xbc88 [& &10.688000] ol_transfer_bin_file 1836: Download Flash data len 2116 [& &10.708000] ol_transfer_bin_file 1783: Download Firmware data len 214312 [& &11.628000] ol_ath_attach() Download FW. [& &11.632000] ol_ath_attach() HT Create . [& &11.636000] ol_ath_attach() HIF Claim. [& &11.640000] ol_ath_attach() BMI Done. [& &11.644000] ol_ath_attach() WMI attached. wmi_handle 86e00000 [& &11.648000] +HWT [& &11.656000] CE_recv_buf_enqueue 644 Populate last entry 512 for CE 5 [& &11.660000] CE_recv_buf_enqueue 653 CE 5 wi 511 dest_ptr 0x6a9420 nbytes 0 recv_ctxt 0x86e4bda0 [& &11.672000] -HWT [& &11.672000] HTC Service:0x0300 ep:1 TX flow control disabled [& &11.680000] CE_pkt_dl_len_set CE 4 Pkt download length 64 [& &11.688000] HTC Service:0x0100 ep:2 TX flow control disabled [& &11.696000] wmi_service_ready_event_rx:&&WMI UNIFIED SERVICE READY event [& &11.700000] num_rf_chain :
[& &11.704000] ht_cap_info: : 0000085b [& &11.708000] vht_cap_info :
[& &11.712000] vht_supp_mcs : 0000fffa [& &11.724000] FIRMWARE:P 49 V 16 T 155 [& &11.724000] [& &11.732000] FIRMWARE:_wlan_rtt_enable [& &11.736000] wmi_ready_event_rx:&&WMI UNIFIED READY event [& &11.740000] ol_ath_connect_htc() WMI is ready [& &11.744000] ol_ath_set_host_app_area TODO [& &11.748000] target uses HTT version 2.1; host uses 2.1 [& &11.760000] ol_ath_attach() connect HTC. [& &11.764000] ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. [& &11.776000] ol_regdmn_init_channels: !avail mode 0x1f) flags 0x2150 [& &11.784000] ol_regdmn_init_channels: !avail mode 0x1f) flags 0xa0 [& &11.792000] ol_regdmn_init_channels: !avail mode 0x1f) flags 0xc0 [& &11.796000] ol_regdmn_init_channels: !avail mode 0x1f) flags 0xd0 [& &11.804000] ol_regdmn_init_channels: !avail mode 0x1f) flags 0x150 [& &11.812000] ol_regdmn_init_channels: !avail mode 0x1f) flags 0x10080 [& &11.820000] ol_regdmn_init_channels: !avail mode 0x1f0) flags 0x20080 [& &11.828000] ol_regdmn_init_channels: !avail mode 0x1f0) flags 0x40080 [& &11.836000] Add VHT80 channel: 5210 [& &11.840000] Add VHT80 channel: 5290 [& &11.844000] Add VHT80 channel: 5530 [& &11.844000] Add VHT80 channel: 5610 [& &11.848000] Add VHT80 channel: 5690 [& &11.852000] Add VHT80 channel: 5775 [& &11.856000] Skipping VHT80 channel 5825 [& &11.860000] ol_ath_phyerr_attach: called [& &11.864000] OL Resmgr Init-ed [& &11.868000] Green-AP : Green-AP : Attached [& &11.868000] [& &11.876000] Green-AP : Attached [& &11.880000] ol_if_dfs_setup: called [& &11.884000] ol_if_dfs_attach: ptr=86e9d974, radar_info=87b97c08 [& &11.892000] ol_ath_rtt_meas_report_attach: called [& &11.896000] ol_ath_attach() UMAC attach . [& &11.904000] ol_if_dfs_configure: called [& &11.908000] ol_if_dfs_configure: FCC domain [& &11.912000] ol_if_dfs_disable: called [& &11.916000] ol_ath_attach: Calling ol_if_dfs_configure [& &11.920000] __ol_ath_attach: init tx/rx TODO [& &11.924000] __ol_ath_attach: hard_header_len reservation 58 [& &11.932000] SC Callback Registration for wifi1 [& &11.980000] ath_attach_dfs[12518] dfsdomain 1 [& &12.048000] VAP device ath0 created ath0 Interface doesn't accept private ioctl... ForBiasAuto (8BE0): Operation not permitted [& &12.128000] [& &12.128000]&&DES SSID SET=TP-LINK_XXXX [& &12.144000]&&ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 [& &12.644000] FWLOG: [16123] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x460, 0x460, 0x0 ) [& &12.652000] FWLOG: [16123] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x460, 0x460, 0x0 ) [& &12.660000] FWLOG: [16123] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x460, 0x460, 0x0 ) [& &12.668000] FWLOG: [16123] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x460, 0x460, 0x0 ) Interface doesn't accept private ioctl... ForBiasAuto (8BE0): Operation not permitted [& &17.512000]&&ieee80211_ioctl_siwmode: imr.ifm_active=918144, new mode=3, valid=1 Local port:1900. Handle Index:1. IGD: adding support to WFADevice [& &19.096000]&&Scan in progress.. Cancelling it [& &19.884000] device ath0 entered promiscuous mode [& &19.888000] br0: port 2(ath0) entering forwarding state Configuration file: /tmp/topology_ath0.conf [& &20.280000]&&ieee80211_ioctl_siwmode: imr.ifm_active=393856, new mode=3, valid=1 [& &20.288000]&&Scan in progress.. Cancelling it [& &20.360000] br0: port 2(ath0) entering disabled state [& &20.368000]&&DEVICE IS DOWN ifname=ath0 ath0: Could not [& &20.372000]&&DEVICE IS DOWN ifname=ath0 connect to kernel driver Using interface ath0 with hwaddr ec:26:ca:xx:xx:xx and ssid 'TP-LINK_XXXX' [& &20.528000] br0: port 2(ath0) entering forwarding state &wlanWarn& Weak &wlanWarn&5g Weak &wlanWarn& 2g/5g wlan warn actived &wlanWarn& on &wlanWarn& wlanWarn call
[& &22.004000] isCountryCodeValid: EEPROM regdomain 0x0 [& &22.012000] ol_regdmn_init_channels: !avail mode 0x1f) flags 0x2150 [& &22.020000] ol_regdmn_init_channels: !avail mode 0x1f) flags 0xa0 [& &22.024000] ol_regdmn_init_channels: !avail mode 0x1f) flags 0xc0 [& &22.032000] ol_regdmn_init_channels: !avail mode 0x1f) flags 0xd0 [& &22.040000] ol_regdmn_init_channels: !avail mode 0x1f) flags 0x150 [& &22.048000] ol_regdmn_init_channels: !avail mode 0x1f) flags 0x10080 [& &22.056000] ol_regdmn_init_channels: !avail mode 0x1f0) flags 0x20080 [& &22.064000] ol_regdmn_init_channels: !avail mode 0x1f0) flags 0x40080 [& &22.068000] Add VHT80 channel: 5775 [& &22.072000] Skipping VHT80 channel 5825 ifconfig: SIOCSIFTXQLEN: No such device [& &22.116000] ath_ioctl: SIOC80211IFCREATE CALLED [& &22.120000] wmi_unified_vdev_create_send: ID = 0 VAP Addr = ec:26:ca:xx:xx:xx: [& &22.128000] VAP device ath1 created ath1 [& &22.168000] [& &22.168000]&&DES SSID SET=TP-LINK_5G_XXXX [& &22.184000]&&ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1 [& &22.192000] OL vap_stop + [& &22.192000] wmi_unified_vdev_stop_send [& &22.196000] OL vap_stop - [& &22.200000] STOPPED EVENT for vap 0 [& &22.212000] ol_ath_desc_alloc_and_mark_for_mcast_clone: VAP Mcast to Unicast buffer allocated: 400 [& &22.220000] ol_ath_vap_set_param: VAP param is now supported param:65 value:2 [& &22.244000] OL vap_stop + [& &22.248000] wmi_unified_vdev_stop_send [& &22.252000] OL vap_stop - [& &22.252000] STOPPED EVENT for vap 0 [& &22.264000] OL vap_stop + [& &22.268000] wmi_unified_vdev_stop_send [& &22.272000] OL vap_stop - [& &22.276000] STOPPED EVENT for vap 0 [& &22.644000] FWLOG: [26646] WHAL_ERROR_RECV_STOPPCU ( 0x110298a, 0x3 ) [& &22.648000] FWLOG: [26646] WHAL_ERROR_RESET_PM (&&) [& &23.220000] mlme_create_infra_bss : Overriding HT40 channel with HT20 channel [& &23.908000] OL vap_start + [& &23.912000] OL vap_start - [& &23.920000] ol_vdev_start_resp_ev [& &23.920000] ol_ath_vap_join: join operation is only for STA/IBSS mode [& &23.928000] ol_ath_wmm_update: [& &23.932000] Notification to UMAC VAP layer [& &27.416000] wmi_unified_vdev_stop_send [& &27.420000] STOPPED EVENT for vap 0 [& &27.872000] OL vap_stop + [& &27.876000] wmi_unified_vdev_stop_send [& &27.880000] OL vap_stop - [& &27.884000] STOPPED EVENT for vap 0 [& &28.016000] OL vap_start + [& &28.016000] OL vap_start - [& &28.020000] ol_vdev_start_resp_ev [& &28.024000] ol_ath_vap_join: join operation is only for STA/IBSS mode [& &28.032000] ol_ath_wmm_update: [& &28.036000] Notification to UMAC VAP layer [& &28.048000] device ath1 entered promiscuous mode [& &28.052000] br0: port 3(ath1) entering forwarding state Configuration fi[& &28.072000]&&ieee80211_ioctl_siwmode: imr.ifm_active=131738, new mode=3, valid=1 le: /tmp/topolog[& &28.084000] wmi_unified_vdev_stop_send y_5G_ath1.conf [& &28.088000] STOPPED EVENT for vap 0 [& &28.096000] br0: port 3(ath1) entering disabled state [& &28.100000]&&DEVICE IS DOWN ifname=ath1 ath1: Could not [& &28.104000]&&DEVICE IS DOWN ifname=ath1 connect to kerne[& &28.112000] OL vap_stop + l driver Using [& &28.116000] wmi_unified_vdev_stop_send interface ath1 w[& &28.120000] OL vap_stop - ith hwaddr ec:26[& &28.124000] STOPPED EVENT for vap 0 :ca:xx:xx:xx and ssid 'TP-LINK_5G_XXXX' [& &28.256000] OL vap_start + [& &28.256000] OL vap_start - [& &28.260000] ol_vdev_start_resp_ev [& &28.264000] ol_ath_vap_join: join operation is only for STA/IBSS mode [& &28.272000] ol_ath_wmm_update: [& &28.276000] Notification to UMAC VAP layer [& &28.280000] br0: port 3(ath1) entering forwarding state [& &28.644000] FWLOG: [33185] WAL_DBGID_BB_WDOG_TRIGGERED ( 0x81a1, 0x200008a, 0x0, 0x9 ) 000a0a02&wlanWarn& already RTNETLINK answers: No such file or directory RTNETLINK answers: No such file or directory Cannot find device &ppp0& [& &30.260000] (tp_mroute_enable_write)146, tp_mroute_enable = 1 -------- new thread -------- -------- new thread -------- -------- new thread -------- [& &33.528000] qca956x_GMAC: GE0 RX DMA ENABLE
TL-WDR6500 mips #1 Wed Sep 17 17:28:37 CST 2014 (none) TL-WDR6500 login: 复制代码
我来恩山就是为了看你！
呐，做人呢，最重要的就是开心
强大的恩山！(以下重复1万次)
能看见usb焊盘，加一个3.3v转5v模块就行
土豪，我们做朋友吧！
我的恩山、我的无线
The best wifi forum is right here.
我的恩山、我的无线
The best wifi forum is right here.
早日 出breed
我的恩山、我的无线
The best wifi forum is right here.
5G啊,感觉离我好遥远...
我的恩山、我的无线
The best wifi forum is right here.
和wdr5600的配置一样？？
我的恩山、我的无线
The best wifi forum is right here.
漂亮,PASCAL有折腾新机了
我的恩山、我的无线
The best wifi forum is right here.
没有usb啊& &
自己飞线啊&
我的恩山、我的无线
The best wifi forum is right here.
配置强，价格还行，双频867。只可惜是百兆。
可以等着买QCA9563的&
我的恩山、我的无线
The best wifi forum is right here.
9561的春天来了！
我的恩山、我的无线
The best wifi forum is right here.
每根天线都有功放？
我的恩山、我的无线
The best wifi forum is right here.
支持一个，128M内存,高档。
我的恩山、我的无线
The best wifi forum is right here.
有线百兆？
我的恩山、我的无线
The best wifi forum is right here.
TP10、TP11两个触点很显眼，只可惜是百兆的LAN，就看看得了
我的恩山、我的无线
The best wifi forum is right here.
好期待,不知道有没有续集
我的恩山、我的无线
The best wifi forum is right here.
这个厉害了，支持
这款路由，百兆lan口是硬伤，还不如1041，至少1041还是千兆wan/lan口。
不过pa和lna还是满喜人的
我的恩山、我的无线
The best wifi forum is right here.
Powered by}